CNC_VERIFY | PROGRAM

Description

Outputs NC program to be compared with already registered one to CNC.

When the data processing on the CNC side is delayed and the data cannot be transferred, this function waits until it can be transferred.
If an application cannot wait, use the cnc_cverify function.

Because importance is attached to the speed of data transfer to the CNC, in general, return of errors(EW_DATA, EW_OVRFLOW, etc.) may be delayed.
Namely, an error status may refrect the result caused by the previously executed cnc_verify callings.
And the error status for some cnc_verify callings just before the finish of verifying is returned by cnc_vrfend function.

Refer to the description of cnc_download function for the format of output data.

MTConnect Fanuc Adapter

Universal Fanuc Driver

Fanuc Focas Library CD

Declaration

Arguments

Return

EW_OK is returned on successful completion, otherwise any value except EW_OK is returned.

The major error codes are as follows.

Return code	Meaning/Error handling
EW_RESET (-2)	HSSB Reset or stop request CNC required to stop verification. 'RESET or STOP' was pushed.(Series 15/15i) Call the cnc_vrfend function. Ethernet Reset or stop request CNC required to stop verification. Call the cnc_vrfend function.
EW_FUNC (1)	cnc_vrfstart function has not been executed.
EW_LENGTH (2)	Data block length error Length of data block(number) exceeds 256 bytes.
EW_DATA (5)	Data error Any difference has been detected during comparing process. A character which is unavailable for NC program is detected. When TV check is effective, a block which includes odd number of characters(including 'LF' at the end of the block) is detected. See Description about the timing of error.

As for the other return codes or the details, see "Return status of Data window function"

CNC option

For HSSB connection,

The extended driver/library function is necessary.

For Ethernet connection,

The Ethernet function and the extended driver/library function are necessary.

However, in case of Series 16i/18i/21i-B, 0i-B/C/F, the required CNC option is as follows.

When Embedded Ethernet is used,

above two optional functions are not required.

When Ethernet board is used,

only Ethernet function is required.

CNC parameter

This function is related to the following CNC parameter.
See the manual of CNC parameter for details.

• Series 15/15i
0020=16(EDIT mode) (must be set) (At HSSB connection)
0022=16(except EDIT mode) (must be set) (At HSSB connection)
0020=7 (EDIT mode) (must be set) (At Ethernet connection)
0022=7 (except EDIT mode) (must be set) (At Ethernet connection)
0000#0
0011#0,2201#0
2210,2211,2212,2213


• Series 16i/18i/21i, 0i, 30i, PMi-A
0000#0
3202#0,#4
3204#3,#4
3210,3211


• Series 16i/18i-W, Power Mate i
0000#0
3202#0,#4
3204#3,#4

CNC mode

Series 15/15i

It is possible to use in any CNC mode.
(It is necessary to set the parameter according to the mode)

Series 16/18/21, 16i/18i/21i, 0i, 30i, Power Mate i, PMi-A

It is possible to use in other than MDI mode.

Available CNC

	0i-A	0i-B/C(Note)	0i-D	0i-F	15	15i	16	18	21	16i-A	18i-A	21i-A	16i-B	18i-B	21i-B	30i-A	30i-B
M (Machining)	H	O	X	X	H	O	H	H	H	O	O	O	O	O	O	H	H
T (Turning)	H	O	X	X	H	-	H	H	H	O	O	O	O	O	O	H	H
LC (Loader)	-	-	-	-	-	-	H	H	H	H	H	H	H	H	H	-	-

	0i-D	0i-F	16i	18i	30i-A	30i-B
P (Punch press)	X	X	O	O	-	H
L (Laser)	-	-	O	-	-	H
W (Wire)	-	-	O	O	H	H

Power Mate i-D	O
Power Mate i-H	O
Power Motion i-A	H

	"O"	:	Both Ethernet and HSSB
	"E"	:	Ethernet
	"H"	:	HSSB
	"X"	:	Cannot be used
	"-"	:	None

Note) 0i-C does not support the HSSB function.

See Also

cnc_vrfstart   cnc_cverify   cnc_vrfend