Description
Deletes the registered Tool management data number from the Magazine management table.
This function searches at the Magazine management table using the magazine number, pot number. And if it finds, it deletes the Tool management data number from the matched entry.
Note) This function is only for "Fast Ethernet board" and "Embedded Ethernet". So, this function is not supported at "Ethernet board".
Universal Fanuc Driver
Fanuc Focas Library CD
Declaration
Arguments
Specify the library handle. See "Library handle" for details.
Specify the pointer to the number of the deleting data for the deletion from the Magazine management table. Set the number of the deleting data(1...) to the pointed data before calling this function.
After the execution of this function, *data_num holds the real deleted number of data.
Specify the pointer to IODBTLMAG2 structure which is used for searching the Tool management data number to be deleted. The IODBTLMAG2 structure is as follows.
typedef struct iodbtlmag2 {
short magazine; /* magazine number */
short pot; /* pot number */
} IODBTLMAG2;
- magazine
- specifies magazine number.
- (Setting range: 1,..,4, 11,..,14, 21,..,24)
- pot
- specifies pot number.
- (Setting range: According to CNC option and CNC parameter)
Return
EW_OK is returned on successful completion, otherwise any value except EW_OK is returned.
The major error codes are as follows.
| Return code | Meaning/Error handling | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
(-1) |
||||||||||
(5) |
In order to get more information for this err_no return value, execute cnc_getdtailerr function. The following detail status will be set onto the member, err_no of OBDERR structure.
|
|||||||||
(6) |
The Tool management function 64 pairs, or the Tool management function 240 pairs, or the Tool management function 1000 pairs. |
|||||||||
(7) |
The Magazine management data table is write protected. |
As for the other return codes or the details, see "Return status of Data window function"
CNC option
This function need the following CNC option.
For HSSB connection,
The extended driver/library function are necessary.
For Ethernet connection,
The Ethernet function and the extended driver/library function are necessary. However, in case of Series 16i/18i/21i-B, 0i-F and 30i, the required CNC option is as follows. When Embedded Ethernet is used,above two optional functions are not required.
When Ethernet board is used,
- only Ethernet function is required.
CNC parameter
This function is related to the following CNC parameter.
See the manual of CNC parameter for details.
13220 (valid number of Tool management data)
13222 (number of data for the 1st magazine)
13223 (starting pot number for the 1st magazine)
13227 (number of data for the 2nd magazine)
13228 (starting pot number for the 2nd magazine)
13232 (number of data for the 3rd magazine)
13233 (starting pot number for the 3rd magazine)
13237 (number of data for the 4th magazine)
13238 (starting pot number for the 4th magazine)
CNC mode
This function can be used in any CNC mode.
Available CNC
| 0i-A | 0i-B/C(Note) | 0i-D | 0i-F | 15 | 15i | 16 | 18 | 21 | 16i-A | 18i-A | 21i-A | 16i-B | 18i-B | 21i-B | 30i-A | 30i-B | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M (Machining) | |||||||||||||||||
| T (Turning) | - | ||||||||||||||||
| LC (Loader) | - | - | - | - | - | - | - | - |
| 0i-D | 0i-F | 16i | 18i | 30i-A | 30i-B | |
|---|---|---|---|---|---|---|
| P (Punch press) | - | |||||
| L (Laser) | - | - | - | - | ||
| W (Wire) | - | - |
| Power Mate i-D | |
| Power Mate i-H | |
| Power Motion i-A | X |
| "O" | : | Both Ethernet and HSSB | |
| "E" | : | Ethernet | |
| "H" | : | HSSB | |
| "X" | : | Cannot be used | |
| "-" | : | None |
Note) 0i-C does not support the HSSB function.
See Also
cnc_regmagazine cnc_rdmagazine cnc_wrmagazine
