CNC_CVERIFY | PROGRAM

Description

Outputs NC program to be compared with already registered one to CNC.

When the data processing on the CNC side is delayed and the next data cannot be transferred, error(EW_BUFFER) is returned.
If an application will wait the data transferring, use the cnc_verify function.

Except the above-mentioned difference, function is the same as "Verify NC program (cnc_verify)", so refer to "cnc_verify" function for other description.

MTConnect Fanuc Adapter

Universal Fanuc Driver

Fanuc Focas Library CD

Declaration

Arguments

Return

EW_OK is returned on successful completion, otherwise any value except EW_OK is returned.

The major error codes are as follows.

Return code	Meaning/Error handling
EW_RESET (-2)	HSSB Reset or stop request CNC required to stop verification. 'RESET or STOP' was pushed.(Series 15/15i) Call the cnc_vrfend function. Ethernet Reset or stop request CNC required to stop verification. Call the cnc_vrfend function.
EW_LENGTH (2)	Data block length error Length of data block(number) exceeds 256 bytes.
EW_FUNC (1)	cnc_vrfstart function has not been executed.
EW_DATA (5)	Data error Any difference has been detected during comparing process. A character which is unavailable for NC program is detected. When TV check is effective, a block which includes odd number of characters(including 'LF' at the end of the block) is detected. See Description about the timing of error.
EW_BUFFER (10)	Buffer full Retry because the buffer is full.

As for the other return codes or the details, see "Return status of Data window function"

CNC option

For HSSB connection,

The extended driver/library function is necessary.

For Ethernet connection,

The Ethernet function and the extended driver/library function are necessary.

However, in case of Series 16i/18i/21i-B, 0i-B/C/F and 30i, the required CNC option is as follows.

When Embedded Ethernet is used,

above two optional functions are not required.

When Ethernet board is used,

only Ethernet function is required.

CNC parameter

This function is related to the following CNC parameter.
See the manual of CNC parameter for details.

• Series 15/15i
0020=16(EDIT mode) (must be set) (At HSSB connection)
0022=16(except EDIT mode) (must be set) (At HSSB connection)
0020=7 (EDIT mode) (must be set) (At Ethernet connection)
0022=7 (except EDIT mode) (must be set) (At Ethernet connection)
0000#0
0011#0,2201#0
2210,2211,2212,2213


• Series 16i/18i/21i, 0i, 30i, PMi-A
0000#0
3202#0,#4
3204#3,#4
3210,3211


• Series 16i/18i-W, Power Mate i
0000#0
3202#0,#4
3204#3,#4

CNC mode

Series 15/15i

It is possible to use in any CNC mode.
(It is necessary to set the parameter according to the mode)

Series 16/18/21, 16i/18i/21i, 0i, 30i, Power Mate i, PMi-A

It is possible to use in other than MDI mode.

Available CNC

	0i-A	0i-B/C(Note)	0i-D	0i-F	15	15i	16	18	21	16i-A	18i-A	21i-A	16i-B	18i-B	21i-B	30i-A	30i-B
M (Machining)	H	O	X	X	H	O	H	H	H	O	O	O	O	O	O	H	H
T (Turning)	H	O	X	X	H	-	H	H	H	O	O	O	O	O	O	H	H
LC (Loader)	-	-	-	-	-	-	H	H	H	H	H	H	H	H	H	-	-

	0i-D	0i-F	16i	18i	30i-A	30i-B
P (Punch press)	X	X	O	O	-	H
L (Laser)	-	-	O	-	-	H
W (Wire)	-	-	O	O	H	H

Power Mate i-D	O
Power Mate i-H	O
Power Motion i-A	H

	"O"	:	Both Ethernet and HSSB
	"E"	:	Ethernet
	"H"	:	HSSB
	"X"	:	Cannot be used
	"-"	:	None

Note) 0i-C does not support the HSSB function.

See Also

cnc_vrfstart   cnc_verify   cnc_vrfend