Description
Deletes the NC program by line basis.
When you specify the line including O number(ex.""Oxxxx""), this function deletes the character after O number, but doesn't delete O number.
Example)
You have the following program you are going to delete by line basis.When you delete 3 lines from the line number 0 for the above program, then you get the following result.O1234(TEST PROGRAM) ; G01 X0. F100 ; X20. ; M30 ; %O1234 M30 ; %
The conditions of the function about CNC mode and the kind of program are as follows.
| EDIT mode | MDI mode | Other mode | |
| MDI program | × | O | × |
| Selected program | O | × | × |
| Not selected program | O | O | O |
If you have the playback option, TJOG/THND mode is the same as EDIT.
This function works normally if OP signal is 1 but STL signal is 0 (for example, feed hold stopping, single block stopping, etc).
When you use this function for the MDI program or the selected program in the following situations, the execution pointer goes to the top of line specified by line_no.
- MDI program in MDI mode.
- Selected program in EDIT mode.
- Selected program in TJOG/THND mode with the playback option.
Universal Fanuc Driver
Fanuc Focas Library CD
Declaration
Arguments : HSSB
Specify the library handle. See "Library handle" for details.
Specify the program number to delete.
When you delete the MDI program, you have to specify -1.
Specify the line number to delete from.
When you delete from the first line of a program, you have to specify 0.
When you specify other than the existing line number, you get EW_DATA error as the return code.
Specify the amount of lines to delete.
If you specify the lines over the last one, the lines between the specified line and before the last one are deleted.
The last line is never deleted.
Return
EW_OK is returned on successful completion, otherwise any value except EW_OK is returned.
The major error codes are as follows.
| Return code | Meaning/Error handling | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
(-1) |
|
|||||||||
(5) |
In order to get more information for this err_no return value, execute cnc_getdtailerr function. The following detail status will be set onto the member, err_no of ODBERR structure.
|
|||||||||
(6) |
The extended driver/library function is necessary. |
|||||||||
(7) |
CNC parameter is a state of write-protection(O8000-/O9000- protection, encoding). Protect KEY signal was ON. (Deletion of the MDI program is excluded)(except 30i/31i/32i, 0i-D/F, PMi-A) |
|||||||||
(12) |
||||||||||
(13) |
|
As for the other return codes or the details, see "Return status of Data window function"
CNC option
For HSSB connection,
The extended driver/library function is necessary.
CNC parameter
This function is not related to CNC parameter.
CNC mode
Available CNC
| 0i-A | 0i-B/C(Note) | 0i-D | 0i-F | 15 | 15i | 16 | 18 | 21 | 16i-A | 18i-A | 21i-A | 16i-B | 18i-B | 21i-B | 30i-A | 30i-B | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M (Machining) | |||||||||||||||||
| T (Turning) | - | ||||||||||||||||
| LC (Loader) | - | - | - | - | - | - | - | - |
| 0i-D | 0i-F | 16i | 18i | 30i-A | 30i-B | |
|---|---|---|---|---|---|---|
| P (Punch press) | - | |||||
| L (Laser) | - | - | - | - | ||
| W (Wire) | - | - |
| Power Mate i-D | |
| Power Mate i-H | |
| Power Motion i-A | H |
| "O" | : | Both Ethernet and HSSB | |
| "E" | : | Ethernet | |
| "H" | : | HSSB | |
| "X" | : | Cannot be used | |
| "-" | : | None |
Note) 0i-C does not support the HSSB function.
See Also
cnc_rdprogline cnc_rdprogline2 cnc_wrprogline cnc_searchword cnc_searchresult
